Horsepower & Torque: 530 Horsepower / 495 ft. lbs. Torque
Cylinder Heads: BluePrint Engines Aluminum Cylinder Heads
Compression Ratio: 10.7:1
Camshaft: Hydraulic Roller Cam - .612 Intake / .585 Exhaust and 225 Intake / 238 Exhaust Duration @ .050 – 113 LSA
Pistons: Hypereutectic
Crankshaft: Nodular Iron Crank - 3.622" Stroke and 6.098" Rods
Fuel Injection: Holley Terminator X Max - Gen IV Complete ECU/Harness EFI System
Fuel Recommendation: 91+ Octane
Does NOT come with a Front Accessory Drive
- Description
- Engine Specs
- Parts & Accessories
- Warranty
Description:
- Horsepower & Torque: 530 Horsepower / 495 ft. lbs. Torque
- Compression Ratio: 10.7:1
- BluePrint Engines Aluminum Heads
- BluePrint Engines Hydraulic Roller Cam
- BluePrint Engines Hypereutectic Pistons
- Nodular Iron Crankshaft
Block:
- BluePrint Engines High Strength Cast Iron (LSX Style) Block
- Increased Deck Thickness and Strength Webbing
- Extended Cylinder Skirt
- Priority Main Oiling
- 6-Bolt Main
- 1-Piece Rear Main Seal
- Improved Water Jacket Design
- Utilizes OEM LS3 Front and Rear Covers
Rotating Assembly:
- Nodular Iron Crankshaft
- 3.622" Stroke
- 6.098" Connecting Rods w/ 150,000 PSI Bolts
- Hypereutectic Pistons
- Internally Balanced Front and Rear
Cylinder Heads:
- BluePrint Aluminum Cylinder Heads - PS8015
- 72cc Chamber
- 2.165" Intake -1.600" Exhaust Valves
- 259cc Intake -102cc Exhaust Runners
Cam Specs:
- Cam Type: Roller Cam
- .612 Intake - .585 Exhaust Lift
- 225 Intake - 238 Exhaust Duration
- @.050-113 Degree Lobe Separation 110 ICL
Holley Terminator X Max Specific Features and Benefits:
- Real Time Fuel Map Learning Simplifies Tuning by Dynamically Adjusting the Base Fuel Rate
- On Board Bosch LSU 4.9 Wideband Control, Enabling Accurate AFR Readings and Closed Loop Tuning
- Eight High Impedance Injector Drivers, Ideal for Stock LS Injectors and Holley EFI Injectors
- Integrated 1-Bar MAP Sensor for Naturally Aspirated or Nitrous Setups, with Harness Support for External Higher Bar Sensors if needed
- 4 Configurable Inputs (12V, Ground, 5V, Frequency) and 2 Outputs (Ground, PWM) - Ideal for Electric Fans, Boost Control Solenoids, Nitrous Control and more
- Free PC Tuning Software via USB/CAN Interface for Full Laptop Control and Advance Setup
- Integrated 3.5" Touchscreen Handheld with Setup Wizard, Internal Data Logging, and Real Time Gauge Displays
- Terminator X Max ECU will Include a Base Timing Map Pre-Configured for this engine
Also Includes:
- Low Profile Swap Oil Pan - BPP81073
- DBW Throttle Body - BPP12191019
- Spark Plugs and Wires
- Fuel Injectors and Rail
- LS3 Intake Manifold
- Harmonic Balancer
- Coil Packs
Assembled with Complete 4l65/70e 4 Speed Automatic Transmission Package:
- 4L65/70E Complete Package
- (1996-2008 13-Pin Harness)
- (1996-2008 13-Pin Harness)
- Electronic Transmission Controller Included
- 2200-2400 Stall Torque Converter
- Flex Plate
- Starter
- First Gear Ratio: 3.059:1
- Second Gear Ratio: 1.625:1
- Third Gear Ratio: 1.000:1
- Fourth Gear Ratio: 0.696:1
Notes:
- This Holley EFI Equipped engine has a fully calibrated ECU by BluePrint Engines. Please DO NOT follow the Holley EFI manual for the calibration of the ECU.
- BluePrint Engines Recommends Air Intake Kit BPPLS01013 to ensure correct MAF calculations and Dyno calibration are maintained with the above ECU / tuning.
- Engine/Trans Package Ships assembled
Cylinder Heads
LS3 Aluminum Cylinder HeadsIgnition Timing
ECM Supplied with CalibrationSpark Plug
.045 in.Firing Order
1,8,7,2,6,5,4,3Rotating Assembly
Nodular Iron Crank - 3.622 in. Stroke and Forged 6.125 in. RodsCam Specs
Hydraulic Roller - .612 Intake / .585 Exhaust Lift - 225 Intake / 238 Exhaust Duration -@.050-113 LSAStall Converter
2200+ RPMYour BluePrint engine was dyno tested with the parts and specifications listed below. If you prefer to install a different part, your engine may not produce the horsepower recorded on your dyno sheet.
Parts & Accessories Specs
| Intake Manifold | BluePrint Engines Cast Aluminum Intake |
|---|---|
| Spark Plug | Champion 3015 / RS14PMC4 |
| Harmonic Balancer | Non-Weighted |
| Flexplate/Flywheel | Non Weighted BPP12654640 - BPPLS1611 |
| Fuel Recommendation | 91 Octane |
Header Partners:
- Click Here for our Header Partners and recommendations.
Better Than the Rest.
The satisfaction of our customers is our highest priority at BluePrint Engines. We use quality components to balance your engine's rotating assembly within two grams of spec. We dyno test your crate engine and certify that it's ready to deliver horsepower and torque.
We give your BluePrint engine the industry's best-in-class warranty for 30-months / 50,000 miles — with the extra confidence only BluePrint can provide. Our warranty applies to individual or professional installations and is fully transferable. View detailed overview
Already Own this engine?
Protect your investment by registering your warranty today. Register below to ensure coverage and stay up to date on important service information.
Register NowEVERY BLUEPRINT ENGINE ACES THE DYNO TEST
We make sure we hit our target horsepower and proper torque with every crate engine. We use an advanced computerized balancer in our in-house dyno testing rooms to get our rotating assemblies within two grams, ensuring silky smooth power over the entire RPM range. That’s precisely why our engines sound and run better than our competitors.
All specs, zero speculation: A comprehensive, dyno-generated printout showing your critical engine specs will accompany your delivered engine — every time. No more guessing or wondering what your installed engine’s real-world peak horsepower and torque ratings actually are. Any doubters in the crowd? Simply flash ‘em your exact engine’s dyno results.